Floor Refinishing Supply Stores Canby OR

Refinishing hardwood floors in Canby, OR takes time, patience, and the proper tools and techniques, but the result can be extraordinary. Supplies you may need in wooden floor refinishing include wide brooms, heavy and light sandpaper, dust masks, wood stain, etc. See below to learn more and to gain access to floor refinishing supply stores in Canby, OR that provide the necessary tools for floor refinishing.

Wilsonville Carpet & Tile Inc
(503) 682-2520
9375 SW Commerce Circle #11
Wilsonville, OR
 
Hagelberger Hardwood Floors, Inc.
(503) 209-5373
2557 Wisteria Court
West Linn, OR

Data Provided By:
CONTRACT FURNISHINGS MART
(503) 542-8900
14160 SW 72ND AVE STE 110
Tigard, OR
 
CRITERION CUSTOM FLOORS
(503) 654-0206
4500 SE CRITERION CT # 100
Milwaukie, OR
 
CORINTHIAN RUG & CARPET CLNG
(503) 786-3170
9800 SE MAIN ST
Milwaukie, OR
 
NAGL FLOOR COVERING
(503) 678-1258
PO BOX 190
Aurora, OR
 
SHAW
(503) 635-2671
1170 OXFORD DR
Lake Oswego, OR
 
PAULSONS FLOOR COVERINGS
(503) 620-7080
10855 SW CASCADE AVE
Tigard, OR
 
CONTRACT FURNISHINGS MART
(503) 655-5277
15140 SE 82ND DR STE 240
Clackamas, OR
 
CARPET MILL OUTLET
(503) 786-3678
9850 SE MAIN ST
Portland, OR
 
Data Provided By:

How to Refinish Your Hardwood Floors

Yes this is another do-it-yourself (DIY) project. Of course you can always hire a professional, but if you are up for the challenge...well here it is!
 
Are your old wooden floor showing wear and tear? All you need to do is refinish them to make them look brand spankin' new!  But before you start you should learn how to refinish hardwood floors - of course. This article will help you get your planning in place.

Sand Away!

First, vacate the room so all you have is the floor. Make sure that all furniture, rugs and other items inside the room are removed. and stored in a safe place. You should also inspect your floor thoroughly and make sure that it does not have any protruding surfaces or have any nails on it. If there are nails in your floor that are sticking out, you should get a hammer and pound them back into the surface.
 
Second, make sure that you are equipped with goggles or a face mask with eye protection to protect yourself from any flying particles and dust. Now it is time to get your floor sander. You can rent this from any equipment rental store. Get something that you can move around easily, and avoid a sander that is too heavy for you to maneuver. Make sure your sander is fitted with the right sand paper.
 
Third, run the sanding machine in the direction of the grains on your wood. Your strokes should be straight and even. Do not stop moving your machine when it is turned on because you will only gauge the floor. In case this happens, you should go back and forth again with the sanding until you even it out.
 
Fourth step, remove your first piece of sandpaper and clip in a new piece with a finer grain into your machine. The fine-grain sandpaper can help even out scratches and lines on your wooden floor.
 
Fifth step, vacuum the room to get rid of all the dust from the sanding.
 

Tips in Beautifying your Floors

When you are finished with the sanding, you can also stain and seal the floors to make them look much better. However, if you prefer the natural color of your wooden floor, there is no need to apply stain. For your finishing touch, brush your wooden floor to get rid of all the sawdust. Use a vacuum cleaner to get rid of other particles. If you do not clean your floor well at this stage, it will only ruin what you have worked hard for. When done with the cleaning, you should ventilate the area by either opening the windows or using an industrial fan to do the job.
 ...

Click here to read the rest of this article from Remodeleze.com